Concrete Coating

Look no further if you’re thinking about having your concrete surface pressure washed, soft washed, coated and/or sealed. Whether it’s your pool deck, sidewalk, driveway, pool coping, tile grout, seawall, or stucco home, just a one-time application of Splash Proof’s nanotechnology coating is adequately procedural. Splash Proof’s revolutionary product line of nanotechnology coating facilitates a super-hydrophobic layer to shield and protect your concrete surface from muggy environmental damages.

Splash Proof is a nanotechnology coating company that offers one-stop-solution of protection from regrowth of mold and mildew that sits stubbornly on concrete surface spanning across residential or commercial properties. Splash Proof’s nanotechnology coating dries clear, non-slippery and gives an additional benefit of 5-year warranty on all ground work performed by certified Splash Proof technicians.

Procedure:

After Splash Proof is contacted for a service, certified technicians get into action to start off the cleaning, coating, and sealing process.

Day 1 – A certified technician examines and evaluates the area to determine the kind of stain removal is required on the surface. Next, the team begins to prepare the surface with a sanitizing and cleaning solution to remove any contamination spread on surfaces such as stains, dirt, mold and or mildew, followed by the process of pressure washing or soft washing. Afterwards, necessary water rinsing of the area is done to clean and clear away deposits of detergents or acids, if any, that were used earlier. The next step is to allow the surface to dry completely leaving it for at least 24 hours.

Day 2 – Prior to the Splash Proof application on the concrete surface, the certified technician inspects to determine if the concrete surface is dry to the touch. Upon certifying, the team begins coating the concrete surface with Splash Proof’s Nanotechnology coating, using either SP-21S solvent based or water-based SP-21W products.

Drying:

Splash Proof normally dries in sunny areas within 2-3 hours but it requires nearly 24-36 hours for curing. Shaded areas, low temperatures, or higher humidity slow down the drying process. The surface may be kept open to foot traffic in 2-3 hours and to vehicular traffic in 24-36 hours. Splash Proof recommends all sprinkler systems be turned off during this time to allow proper curing.

Maintenance:

Splash Proof is a protectant that layers your concrete with super hydrophobic coating thereby reducing mold and mildew. Periodic washing with plain water to keep the area clean is recommended. Acids, gasoline, hydraulic fluids, and motor oil spills need to be removed from the surface as soon as possible.

Contact us for your inquiries and check out our Gallery for Photos before and after Splash Proof services.

Pavers Coating

Whether it’s pavers on your driveway, walkway, pool deck or lanai, exposures to environmental contaminants and constant foot or vehicular traffic destroy the appearance of pavers. No longer you need to worry about constant pressure washing destroying your pavers’ surfaces. Splash Proof self-cleaning nanotechnology coating is a complete solution to keep them looking great for up to a period of 5 years.

Splash Proof has vast and extensive knowledge in using nanotechnology coating that protect and shield pavers from mold and mildew. Nanotechnology coating for your pavers also deliver the benefit of longer lifespan and protect it from future stains such as soda, juice, gum adhesion, and more.

Procedure:

Day 1 – A certified technician checks and appraises the surface to verify the type of stain removal service is necessary. Next, the technicians use sanitizing and cleaning solutions to eliminate contaminates on the surface. After removing stains, dirt, mold and/or mildew, pressure washing and water rinsing is done to take away residues of detergents or acids, if they were used previously. Finally, the surface is left to completely dry for up to 24 hrs.

Day 2 – Prior to the application of color enhancing nanotechnology coating. Certified technicians replenish any sand lost from cleaning to the paver joints. Upon completion of sanding and pavers are dry to the touch, the team begins application of the SP-22W water based nanotechnology coating or the SP-21S solvent based nanotechnology coating.

Drying:

Splash Proof dries quickly in sunny locations within 2-3 hours with a curing time of 24-36 hours. Dark shaded areas, low temperatures, or higher humidity require more hours for drying process. The paver may be kept open to foot traffic in 2-3 hours and to vehicular traffic in 24-36 hours. For proper curing, Splash Proof suggests to turn off all sprinkler systems.

Maintenance:

Splash Proof is a protectant that layers your pavers coating with a super hydrophobic coating thereby reducing mold and mildew. Periodic washing with plain water to keep the area clean is recommended. Acids, gasoline, hydraulic fluids, and motor oil spills need to be removed from the surface as soon as possible.

Contact us for your inquiries. Check out our Gallery for Photos before and after Splash Proof services.

Pavers Color Enhancement

Pavers are very versatile and an excellent choice for your landscape and hardscape designs, but over time the paver color starts to inevitably fade and lose its appeal. Restoring pavers brings back its original color and prevents erosion. Splash Proof team of professional technicians assist you in restoring your pavers.

The installation of our color enhancing nanotechnology coating gives pavers a hydrophobic protection that reduces the stockpile of mold and mildew. A one-time application is all that is needed to enjoy the beauty of your home or commercial property. Splash Proof nanotechnology coating is weather and waterproof with a 5-year warranty.

Procedure:

Day 1 – A certified technician visits the premises to check and verify the service required for pavers. Next, the team begins the process to sanitize and clean the debris on the pavers. After ensuring the stain and dirt s removed, pressure washing and soft washing is performed. This is further followed by water rinsing that takes away detergents and/or acids, if they were previously applied. Pavers are then allowed to dry for 24 hours.

Day 2 – Prior to the application of color enhancing nanotechnology coating, certified technicians replenish any sand lost from cleaning to the paver joints. Upon completion of sanding and pavers are dry to the touch, the team begins application of the SP-23E color enhancing nanotechnology coating.

Drying:

Splash Proof dries quickly in sunny locations within 2-3 hours with a curing time of 24-36 hours. Dark shaded areas, low temperatures, or higher humidity require more hours for drying process. The paver may be kept open to foot traffic in 2-3 hours and to vehicular traffic in 24-36 hours. For proper curing, Splash Proof suggests to turn off all sprinkler systems.

Maintenance:

Splash Proof is a protectant that layers your pavers coating with a super hydrophobic coating thereby reducing mold and mildew. Periodic washing with plain water to keep the area clean is recommended. Acids, gasoline, hydraulic fluids, and motor oil spills need to be removed from the surface as soon as possible.

Contact us for your inquiries. Check out our Gallery for Photos before and after Splash Proof services.

Stone Coating

Natural Stones such as – sandstone and travertine are high-end building materials used for indoor and outdoor surfaces. Coating or sealing for unpolished stones is highly recommended to add durability and restore its beautiful texture. Environmental damages also contribute to the factors for identifying the causes as to why sealing or coating for natural stones is a necessity. Splash Proof nanotechnology coating is well sought-after for its super hydrophobic properties.

Splash Proof long-standing nanotechnology coating ensures promising results for up to 5 years. The natural stone nanotechnology coating is not affected by any weather changes and remain waterproof due to its penetration into the surfaces’ pores. The surfaces get natural look and stay non-slippery and this is most perfectly suitable for pool decks, pool copings, driveways, and many more regularly-used areas.

Procedure:

Day 1 – A certified technician visits the premises to check and verify the services required for the natural stone surfaces. Next, the team begins the process to sanitize and clean the debris on the surface. After ensuring the stain and dirt is removed, pressure washing and soft washing is performed. This process of water rinsing takes away detergents and/or acids, if they were previously applied. Natural stone surface is then allowed to dry for 24 hours.

Day 2 – Prior to the application of nanotechnology coating, certified technicians replenish any sand lost from cleaning the natural stone joints and also if natural stones are not grouted. Upon completion of sanding and when natural stones are dry to the touch, certified technicians begin the application of the SP-21S solvent based nanotechnology coating or SP-22W water-based nanotechnology coating.

Drying:

Splash Proof normally dries in sunny areas within 2-3 hours but it requires nearly 24-36 hours for curing. Shaded areas, low temperatures, or higher humidity may slow down the drying process. The surface may be kept open to foot traffic in 2-3 hours and to vehicular traffic in 24-36 hours. Splash Proof recommends all sprinkler systems be turned off during this time to allow proper curing.

Maintenance:

Splash Proof is a protectant that layers your stone surface with super hydrophobic coating thereby reducing mold and mildew. Periodic washing with plain water to keep the area clean is recommended. Acids, gasoline, hydraulic fluids, and motor oil spills need to be removed from the surface as soon as possible.

Contact us for your inquiries. Check out our Gallery for Photos before and after Splash Proof services.

Tile Roof Coating

Barrel roof tiles also known as Spanish Tiles or Roman Double Tiles are aesthetically very appealing. Tile roofs accommodated on commercial or residential property, with proper installation and care, are popularly known to last between 50-100 years. Many roof tile manufacturers recommend tile roofs to be coated or sealed for added protection as sun exposure is more severe on roof tops.

Protect your investment with Splash Proof nanotechnology coating. Splash Proof nanotechnology coating penetrates the tile roofs’ pores and holds as a part of the substrate. The treated tile roof is super hydrophobic reducing the growth of unsightly mold and mildew for up to 10 years.

Procedure:

Day 1 – A certified technician and a licensed roofing contractor may make a site visit to determine if any repairs are needed. After inspection, licensed roofing contractor carries out necessary repairs before coating process is taken up. Upon completion of repairs, certified technicians carefully begin covering and watering down of vegetation to prevent damages. Certified technicians use a cleaning and sanitizing solution to remove all debris including mold and mildew. Soft washing is performed to prevent damages to fragile roof tiles. After this step, the tile roof may be left to dry for up to 24 hrs.

Day 2 – Prior to the application of nanotechnology coating, certified technicians determine if the tile roof is dry to the touch. After certifying, the team applies Splash Proof nanotechnology coating, using either SP-21S solvent based or water-based SP-21W products.

Drying:

Splash Proof dries quickly in sunny locations within 2-3 hours with a curing time of 24-36 hours. Dark shaded areas, low temperatures, or higher humidity require more hours for drying process. The surface may be kept open to foot traffic in 2-3 hours and to vehicular traffic in 24-36 hours. For proper curing, Splash Proof suggests to turn off all sprinkler systems.

Maintenance:

Splash Proof is a protectant that layers your tile roof with a super hydrophobic coating thereby reducing mold and mildew. Periodic washing with plain water to keep the area clean is recommended. Acids, gasoline, hydraulic fluids, and motor oil spills need to be removed from the surface as soon as possible.

Contact us for your inquiries. Check out our Gallery for Photos before and after Splash Proof services.

Travertine Color Enhancement

Travertine is a naturally porous non-slippery stone. It is an easy choice for pool decks, patios, pool copings, and driveways. If travertine is unpolished, our certified technicians highly recommend it to be sealed or coated. With environmental exposures, travertine gets damaged and loses its lustrous appearance. Splash Proof nanotechnology coating does not simply sit on top of the surface like traditional coatings or sealers. Our nanotechnology coating penetrates deep down into the travertine capillaries and occupies a part of the substrate. The travertine surface turns into hydrophobic that reduces the growth of mold and mildew. Splash Proof color enhancing nanotechnology coating escorts color to your travertine and lasts for up to 5 years.

Procedure:

Day 1 – A certified technician visits the premises to check and verify the services required for the travertine surface. Next, the team begins the process to sanitize and clean the debris on the surface. After ensuring the stain and dirt has been removed, pressure washing and soft washing is performed. Water rinsing takes away detergents and/or acids, if they were previously applied. Travertine surface is then allowed to dry for 24 hours.

Day 2 – Prior to the application of color enhancing nanotechnology coating, certified technicians replenish any sand lost from cleaning to the travertine joints if travertine is not grouted. Upon completion of sanding and when travertines are dry to the touch, certified technicians begin application of the SP-23E color enhancing nanotechnology coating.

Drying:

Splash Proof normally dries in sunny areas within 2-3 hours but it requires nearly 24-36 hours for curing. Shaded areas, low temperatures, or higher humidity may slow down the drying process. The surface may be kept open to foot traffic in 2-3 hours and to vehicular traffic in 24-36 hours. Splash Proof recommends all sprinkler systems be turned off during this time to allow proper curing.

Maintenance:

Splash Proof is a protectant that layers your travertine with a super hydrophobic coating thereby reducing mold and mildew. Periodic washing with plain water to keep the area clean is recommended. Acids, gasoline, hydraulic fluids, and motor oil spills need to be removed from the surface as soon as possible.

Contact us for your inquiries. Check out our Gallery for Photos before and after Splash Proof services.

Location

PO Box 771237 Coral Springs fl 33077

Phone

(954) 494-1594

Email

sales@splashprooflegacy.com

Open Hours

Mon: 9am - 6pm
Tue: 9am - 6pm
Wed: 9am - 6pm
Thur: 9am - 6pm
Fri: 9am - 6pm
Sat: 9am - 5pm
Sun: Closed

Send A Message

Splash Proof Legacy